ImmersionRC Tramp HV 600mW 5.8GHz Video Transmitter (US Version)

(16 reviews) Write a Review
  • ImmersionRC Tramp HV 600mW 5.8GHz Video Transmitter (US Version)
  • ImmersionRC Tramp HV 600mW 5.8GHz Video Transmitter (US Version)
  • ImmersionRC Tramp HV 600mW 5.8GHz Video Transmitter (US Version)
  • ImmersionRC Tramp HV 600mW 5.8GHz Video Transmitter (US Version)
  • ImmersionRC Tramp HV 600mW 5.8GHz Video Transmitter (US Version)

Out of stock


Tramp HV 600mW 5.8GHz Video Transmitter

The all new Trampoline HV (TrampHV for short) is a tiny video transmitter with a huge set of features! At only 4 grams, it promises to solve the majority of issues and delays that race events have been experiencing.

Pit Mode: Pit mode transmits a tiny amount of power on a pre-defined frequency to allow for quad setup at a race event without disrupting the show.

Touch ’n’ Race: Transmitters are placed in Race mode upon arrival at a race event, and remain in that mode until the event is over. Race directors can, without powering up a model, define the frequency and power output of the transmitter in 5 seconds flat before a race starts. This means more practice runs, more qualifiers, and races which start and finish on-time

LapRF Compatible: LapRF uses the energy emitted by the 5.8GHz transmitter on the quadcopter to trigger a lap timer sensor.

Anti-Glitch: Anti-Glitch is a new technology which allows video transmitters to power up cleanly on their assigned channel without affecting neighboring channels.

Calibrated Power: Each and every TrampHV is factory calibrated to ensure precise power outputs, especially at the critical low-power race levels.


  • Size: 32mm x 14mm x 5mm
  • Weight: 4g (without SMA cable)
  • Input Voltage: 2s - 6s LiPo (7v - 26v)
  • Output Voltage: 5v for FPV camera
  • Power output: 1 - 600mW
  • Channels: 40 standard US Channels
  • Antenna Connector: SMA
  • Built in Thermal Protection


  • 1x ImmersionRC Tramp HV 5.8GHz Video Transmitter
  • 1x RFID Race Programmer Receiver
  • 1x RFID Race Programmer cable
  • 1x video cable with camera and power connectors
  • 1x spare transmitter cable with connector




The use and operation of this type of product in the USA and many other countries may require a license and some countries may forbid its use entirely. In the USA, you will need a "HAM" amateur radio license. Learn more about HAM licenses, and find a HAM license exam session in your areaIt is your responsibility to ensure that the use of this product meets the requirements imposed by your government's rules and regulations for RF devices. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them. Rotor Riot cannot be held responsible for your actions if you purchase and/or use this product in violation of your government's regulations. By agreeing to our terms and conditions during the check-out process, you also agree to have read and to understand this notice.

View AllClose

16 Reviews

  • 5
    ImmersionRC TNR TrampHV

    Posted by Arthur Krasnopolski on May 18th 2018

    What can I say? Another quality product from ImmersionRC. Has it on two builds at this moment and really happy about this transmitter

  • 5
    Best 5.8GHz transmitter I've seen so far

    Posted by MaEtUgR on Apr 26th 2018

    This one is a safe bet. With TBS Triumph antenna and 600mW I get 850meters LOS range max. I never had a problem with multiple of these, they survived crashes, they don't disturb other frequencies. I can only recommend.

  • 1
    used to work not anymore.. junkkkk

    Posted by Aaron on Apr 16th 2018

    they do not have customer service.0

  • 5
    Best Bang for your Buck

    Posted by Sasquatch on Mar 14th 2018

    This transmitter is every bit as good as the unify, and its $20 cheaper. Immersion makes some great products and this is one of them. This VTx is a beast, and so easy to install. Plus if you add the smart wand you can adjust everything without the hassle of going through an OSD (if you even have OSD). Basically you can't go wrong woth this and for the price you can damn near buy two for the price of one Unify.

  • 1
    Good VTX, horrible Rotorriot support

    Posted by Maciej Zybura on Feb 12th 2018

    Well, VTX works as supposed to. It is great part. Unfortunately RotorRiot has no support at all and they are ignoring user requests and messages. If You are not famous Youtuber than You will probably will be ignored and has no support as i do. Important message regarding my placed and not shipped request was ignored and not answered till today. It was way over two weeks. I suppose that warranty or return requests looks the same. Be warned.

  • 5
    Best VTX

    Posted by Greg "The Mech" Elliott on Nov 14th 2017

    Lowest video noise of anything I have tried to date! And I have Fatshark, Imersion RC as well as some other cheaper ones. Great range, Low Vid Noise, what more do you want. I will be buying more of these!

  • 5
    Cannot wait to test lua scripts with Taranis

    Posted by Ian McBeth on Nov 5th 2017

    will keep you updated with the subject line(ease of use ETC). normally have been a TBS unify pro guy, but sometimes change it good.

  • 5
    Just awesome

    Posted by RC on Oct 2nd 2017

    With the ability to make changes via FPV this is by far the best product. It will be hard for me to use another product.

  • 5

    Posted by Franck on Sep 10th 2017

    2S-6S version is perfect for my use ;)
    Perfect with Betaflight and Taranis LUA support.
    Great product

View AllClose