"The Remix" FPV Freestyle Frame by ummagawd (Purple)

(8 reviews) Write a Review
  • "The Remix" FPV Freestyle Frame by ummagawd (Purple)
  • "The Remix" FPV Freestyle Frame by ummagawd (Purple)
  • "The Remix" FPV Freestyle Frame by ummagawd (Purple)
  • "The Remix" FPV Freestyle Frame by ummagawd (Purple)


The Ummagawd Remix FPV Freestyle Frame

Our team pilot Tommy Tibajia dreamed of something that existing FPV frames were not able to provide - a truly balanced quad with most of the weight as close to the CG as possible. After over half a year of design work and testing, as well as many iterations of prototypes, Tommy’s dream has come true.

The Ummagawd Remix FPV Frame, unofficially dubbed “the Ummakwad”, has been designed to put most of the weight of the quad as close as possible to the center of gravity. It was no easy task to rethink the way traditional mini quads are built, but the end result looks and performs extremely well!


In order to centralize the weight, the electronic components are installed under the center plate, and the battery is placed sideways across the top of the frame. This gets the bulk of the mass in the very center of the frame and in line with the propellers, the source of thrust. Centralized 4 in 1 ESC systems are favored for this build, to maintain the theme of centralized weight distribution.

Ummagawd's recommended choice of FC/ESC stack: 
Hobbywing XRotor F4 MicroCube Flight Controller + 40A 4-in-one ESC

See related items below for more recommended parts!


Unlike some frames on the market, the Remix frame is super easy to work on. The bottom cover plate opens like the hood of a car, giving easy access to the electronics stack for building and repair. The arms are also really easy to replace when the limits you are pushing push back on your quad.

The FPV camera on the Ummagawd Remix is mounted in a carbon rollcage of sorts - so it’s protected from crashes that might otherwise destroy the camera or lens. The rollcage is angled upwards, so that it can allow high camera tilt - making it suitable for both freestyle and racing. The rollcage also serves as a tilted mount for a GoPro Session camera, so you’re one step closer to getting great HD footage!

Another interesting feature of the Ummagawd Remix frame is the slot on each arm for the motor wires. They keep the motor wires from sliding around over the edge of the arm, and prevent damaged or bent propellers from cutting the motor wires.


The Ummagawd Remix does not fall short when it comes to good looks. Not only does it have titanium screws and purple anodised hardware, but it also has custom designed aluminum parts and a high quality battery pad. The carbon fiber used is top notch quality, and the chamfered edges that make the Remix feel great to the touch.



  • TrueX Motor Layout

  • Well-balanced Layout

  • Durable and Lightweight Design

  • High Quality Carbon Fiber with Chamfered Edges

  • Purple Anodized Hardware

  • Custom CNC Aluminum parts

  • Quick Access to electronics compartment

  • Adjustable FPV Camera Mount

  • Top Mounted Battery

  • Exchangeable Arms

  • Grade 2 Titanium Hardware


     “Definitely flies better… and it behaves very well. Huge difference from my other frames, I prefer the remix 1000x”

     “The frame has really good flight properties”




The first production batch includes "skid discs". These skid discs are optional, they are intended to be an aftermarket accessory for those who want to do some heavy skidding with their kwad. The idea is that the discs would wear out before the carbon sled. In fact, you could also use a metal washer or even titanium for some cool sparks!
The included instruction manual is an older version, don't freak out... it still has all of the info you need to build... it's just slightly confusing about an optional feature. There is a single m3x14mm bolt showing behind the session plate. This is NOT needed to put together the frame and is actually there for future after market accessories created by 3d print manufacturers... Futureproofing! 
Tolerances: you might find it difficult to get the m3 locknuts into the carbon. In fact, it might even seem impossible. Don't worry... it just takes some light filing to press it in. It's suggested that you take only a few passes with the file and test fit. When designing these parts, we have to take into account manufacturing tolerances of both the carbon as well as the locknuts. It's important these locknuts are a tight fit, otherwise you risk it spinning when you tighten them down. Worst case scenario, you also file the locknuts as well... but we have not run into that situation. We would rather it be a tight fit, than to have something too loose.
The bottom rear back plate will be a bit loose. The reason is because the slots holding that plate in is designed for a future expansion board (LED board, buzzer/mic, etc.). The standard PCB board thickness is 1.6mm, the blank plate included is 1.5mm. It does not lend to the structural integrity of the frame and so it being loose, is OK. We just wanted to include a blank frame in case you found a use for it, or wanted to attach the license plate sticker included in the kit!
View AllClose

Additional Information

View AllClose

8 Reviews

  • 5
    El Remix 5

    Posted by monchovega@live.com on Dec 5th 2018

    Este frame es Perfecto muy facil de armar

  • 5
    El Remix 5

    Posted by monchovega@live.com on Dec 5th 2018

    Este frame es Perfecto muy facil de armar

  • 5
    The Remix Frame

    Posted by EDWARD BLAKENY on Aug 14th 2018

    Excellent frame. love it.

  • 5
    The Unnagawd Remix frame

    Posted by Frank Graziano on Aug 5th 2018

    This is an excellent frame. Easy to build and looks awesome. I love the anodized aluminum accents and the ease of maintenance with the bottom hatch. Very well though out frame. Did the build Tommy did on rotor riot and it flies like a dream. Even added the ummagawd LED strip. Awsome!!

  • 5

    Posted by Dominique on Jul 31st 2018

    Loved the purple over gold. Not only is this a well made frame but loved that there is youtube videos for the complete build. Thats what really made me pull the trigger. Small draw back is that i had to do some filling. But didnt mind to much as i was able to get the tolerance how i wanted it. I just wish they had more colors purple is my favorite but wanted to buy a second one.. maybe if they had all black washer set an rods id buy a second one im just not into gold which is why i wish they could be customize a bit more with color. Very happy though!!!

  • 5

    Posted by Mark on Jul 7th 2018

    Best frame I’ve flown! I’d sell every other frame I own and keep this if I could only have one quad. Mid mount CG allows for a very smooth flight characteristic and tunes easily. Very nimble. You’ll regret not having one.

  • 5
    Awesome frame

    Posted by Leon Monsalud on Jun 26th 2018

    This frame has taken so much abuse and is still in one piece. It helps to have arm guards on to prolong the life of the frame.

  • 3
    Good overall but screws are horrible

    Posted by Ignacy Wozniak on Jun 24th 2018

    The titanium screws are horrible I tightened the remix already built and when I Check motor direction 3 motors are wrong so I wanted to change the motor wire positioning on my esc except the screw hex hole turned into a circle and I can’t open it at all( the screw molded to my driver) and now I haven’t been flying for a month 1 week because of the screw 2 because my last frame broke and I was reasearching a good frame.

View AllClose